Moderators: pcwzrd13, deluxux, VasiliyRS
RazorX wrote:gilvan666 wrote:RazorX wrote:make sure for the memory card emulator pcb you flash the arcade stick firmware on it in order for it to work.
also the connector i used was JST-5-PTH.
where did you buy it? I didn't find it on aliexpress
just search google for a place to buy them, i never use aliexpress for anything.
i buy my stuff from either ebay, amazon or a site such as Farnell etc.
gilvan666 wrote:RazorX wrote:gilvan666 wrote:
where did you buy it? I didn't find it on aliexpress
just search google for a place to buy them, i never use aliexpress for anything.
i buy my stuff from either ebay, amazon or a site such as Farnell etc.
RazorX came to PCBs, as soon as I get the rest of the components I'll assemble one to use.
I still haven't found the JST-5-PTH to buy, could you send the link where you bought it?
RazorX wrote:i can now confirm those are correct, the 2.00mm 5-Pin Angled JST PH Style Connectors have arrived and fit perfectly on my pcbs.
gilvan666 wrote:RazorX wrote:i can now confirm those are correct, the 2.00mm 5-Pin Angled JST PH Style Connectors have arrived and fit perfectly on my pcbs.
thanks for the confirmation.
a doubt which reference of the diodes to use in this pcb?
RazorX wrote:gilvan666, did you manage to get your board setup and working?
gilvan666 wrote:RazorX wrote:gilvan666, did you manage to get your board setup and working?
Waiting for my SMT32F103C8T6 to arrive, that's all it's missing.
RazorX knows the differences between the STM32F103C8T6
SMT32F103C6T6 ?
gilvan666 wrote:RazorX knows the differences between the STM32F103C8T6
SMT32F103C6T6 ?
Code: Select all
ARM®32-bit Cortex®-M3 CPU Core
- 72 MHz maximum frequency,1.25 DMIPS/MHz (Dhrystone 2.1) performance at 0 wait state memory access
- Single-cycle multiplication and hardware division
Memories
- 64 or 128 Kbytes of Flash memory
- 20 Kbytes of SRAM
Clock, reset and supply management
- 2.0 to 3.6 V application supply and I/Os
- POR, PDR, and programmable voltage detector (PVD)
- 4-to-16 MHz crystal oscillator
- Internal 8 MHz factory-trimmed RC
- Internal 40 kHz RC
- PLL for CPU clock
- 32 kHz oscillator for RTC with calibration
Low-power
- Sleep, Stop and Standby modes
- VBAT supply for RTC and backup registers
2 x 12-bit, 1 µs A/D converters (up to 16 channels)
- Conversion range: 0 to 3.6 V
- Dual-sample and hold capability
- Temperature sensor
DMA
- 7-channel DMA controller
- Peripherals supported: timers, ADC, SPIs, I2Cs and USARTs
Up to 80 fast I/O ports
- 26/37/51/80 I/Os, all mappable on 16 external interrupt vectors and almost all 5 V-tolerant
Debug mode
- Serial wire debug (SWD) & JTAG interfaces
7 timers
- Three 16-bit timers, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input
- 16-bit, motor control PWM timer with dead-time generation and emergency stop
- 2 watchdog timers (Independent and Window)
- SysTick timer 24-bit downcounter
Up to 9 communication interfaces
- Up to 2 x I2C interfaces (SMBus/PMBus)
- Up to 3 USARTs (ISO 7816 interface, LIN, IrDA capability, modem control)
- Up to 2 SPIs (18 Mbit/s)
- CAN interface (2.0B Active)
- USB 2.0 full-speed interface
CRC calculation unit, 96-bit unique ID
Packages are ECOPACK
Code: Select all
ARM 32-bit Cortex-M3 CPU Core
- 72 MHz maximum frequency,1.25 DMIPS/MHz (Dhrystone 2.1) performance at 0 wait state memory access
- Single-cycle multiplication and hardware division
Memories
- 16 or 32 Kbytes of Flash memory
- 6 or 10 Kbytes of SRAM
Clock, reset and supply management
- 2.0 to 3.6 V application supply and I/Os
- POR, PDR, and programmable voltage detector (PVD)
- 4-to-16 MHz crystal oscillator - Internal 8 MHz factory-trimmed RC
- Internal 40 kHz RC
- PLL for CPU clock
- 32 kHz oscillator for RTC with calibration
Low power
- Sleep, Stop and Standby modes
- VBAT supply for RTC and backup registers
2 x 12-bit, 1 µs A/D converters (up to 16 channels)
- Conversion range: 0 to 3.6 V
- Dual-sample and hold capability
- Temperature sensor
DMA
- 7-channel DMA controller
- Peripherals supported: timers, ADC, SPIs, I2Cs and USARTs
Up to 51 fast I/O ports
- 26/37/51 I/Os, all mappable on 16 external interrupt vectors and almost all 5 V-tolerant
Debug mode
- Serial wire debug (SWD) & JTAG interfaces
6 timers
- Two 16-bit timers, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input
- 16-bit, motor control PWM timer with dead-time generation and emergency stop
- 2 watchdog timers (Independent and Window)
- SysTick timer 24-bit downcounter
6 communication interfaces
- 1 x I2C interface (SMBus/PMBus)
- 2 × USARTs (ISO 7816 interface, LIN, IrDA capability, modem control)
- 1 × SPI (18 Mbit/s)
- CAN interface (2.0B Active)
- USB 2.0 full-speed interface
CRC calculation unit, 96-bit unique ID
Packages are ECOPACK
Return to “New Releases/Homebrew/Emulation”
Users browsing this forum: No registered users