Adapter for MAPLE (Release)

[zjj0251]

did this FW works for 96x64 only or adjust size with automatic?
such as 480x320. I want to try a bigger SPI LCD,and build a huge VMU,must be interesting

only for display nokia 1202/1203/1280
controllers of other displays are not supported, there is no feedback from the display controller, therefore it is impossible to make support for several types of displays

Tks! so u just make a double display output via SPI,am I right?
I think it will shows 96x64 on the left top when I use a big(maybe 480x320) LCD,if change the output in program maybe get a full display,can‘t wait to test.

[Dakangel]

did this FW works for 96x64 only or adjust size with automatic?
such as 480x320. I want to try a bigger SPI LCD,and build a huge VMU,must be interesting

only for display nokia 1202/1203/1280
controllers of other displays are not supported, there is no feedback from the display controller, therefore it is impossible to make support for several types of displays

How ironic, i was about to recomend these super cheap aliexpress displays just before you post that.
All their description pages comes with schematics and some are compatible with the stm32 chips:

1.4 inch 3.3V 128x64 lcd display dot matrixs st7567 10Pin spi serial port reflective monochrome Grey New display

3.3v 96*65 96x65 Graphic Display 14P SPI Serial Port White Backlight FSTN NEW LCD ST7565 TM9665ACCWgWC4 Medical Instrument

0.96 inch IIC SPI Serial 7/4Pin White/Blue/Yellow Blue/Yellow OLED Display Module SSD1306 12864 LCD Screen Board for Arduino

1.4 inch 128x64 128*64 COG 12864 LCD Module st7565 Controller 3.3V/5V Gray and white Backlight 8PIN 4 wires SPI interface

Check it out please, as an alternative for the nokia unavailable ones you use right now.

[megavolt85]

Tks! so u just make a double display output via SPI,am I right?

yes, but there is not enough processor time, I update the display in two passes

I think it will shows 96x64 on the left top when I use a big(maybe 480x320) LCD,if change the output in program maybe get a full display,can‘t wait to test.

there is not enough free processor time for this
any display needs to be initialized when turned on, each display controller uses its own initialization string, so you cannot connect the display with another controller without changing the firmware

[megavolt85]

How ironic, i was about to recomend these super cheap aliexpress displays just before you post that.
All their description pages comes with schematics and some are compatible with the stm32 chips:

Check it out please, as an alternative for the nokia unavailable ones you use right now.

128x64 displays will look bad
this one is pretty good
3.3v 96*65 96x65 Graphic Display 14P SPI Serial Port White Backlight FSTN NEW LCD ST7565 TM9665ACCWgWC4 Medical Instrument

[CrazyIcecap]

i just finished a second version of the case.
This one has the cables going from left to right, and with fixatures for cable and STM32.
Also 2 different lids: one with a fixature for the display.

It is now available on thingiverse, too.
https://www.thingiverse.com/thing:5324101

[CrazyIcecap]

First time i used Arcade Stick and Adaptor on a Con (LuheCon in Germany, today). Works great and is a lot of fun!

[CrazyIcecap]

How ironic, i was about to recomend these super cheap aliexpress displays just before you post that.
All their description pages comes with schematics and some are compatible with the stm32 chips:

Check it out please, as an alternative for the nokia unavailable ones you use right now.

128x64 displays will look bad
this one is pretty good
3.3v 96*65 96x65 Graphic Display 14P SPI Serial Port White Backlight FSTN NEW LCD ST7565 TM9665ACCWgWC4 Medical Instrument

Does this display work with your firmware?

[megavolt85]

Does this display work with your firmware?

no, only display from nokia 1202 is supported, I don't have any others

[tiochico27]

When the firmware will be available?

[rpf16rj]

STM32F401CCU6 84MHz ARM STM32 Cortex-M4 Core Development Board 5V

yep

stm32f401ссu6.png

@megavolt85 I have been following this project, is a great job.

The fw for f401 board has launch? I not finded.