Page 46 of 88

Re: USB4MAPLE adapter

Posted: Wed May 22, 2024 3:51 pm
by MoeFoh
megavolt85 wrote: Wed May 22, 2024 3:11 pm
MoeFoh wrote: Wed May 22, 2024 2:18 pm New one - 8bitdo Ultimate 2.4g wired d-input.
seems no different from Pro 2, didn’t add new code, just added this PID to Pro 2
test it
usb4maple(22.05.24).7z
Yep, it's a Pro 2 in a different form factor: :lol:

2 changes:
Twin Stick mode:
U is D
D is U
on RS
(reversed)

FPS mode:
LB is U
RB is D
(reversed)

Doing both of these on both controllers (makes sense).

Everything else looks great!

Re: USB4MAPLE adapter

Posted: Wed May 22, 2024 4:12 pm
by megavolt85
MoeFoh wrote: Wed May 22, 2024 3:51 pm Yep, it's a Pro 2 in a different form factor: :lol:
fixed
usb4maple(22.05.24).7z
(51.75 KiB) Downloaded 143 times

Re: USB4MAPLE adapter

Posted: Wed May 22, 2024 5:01 pm
by MoeFoh
megavolt85 wrote: Wed May 22, 2024 4:12 pm
MoeFoh wrote: Wed May 22, 2024 3:51 pm Yep, it's a Pro 2 in a different form factor: :lol:
fixed
usb4maple(22.05.24).7z
Buttons all good.

No vibration ability detected. 240p TS doesn't show a JumpPack like it should.

Re: USB4MAPLE adapter

Posted: Wed May 22, 2024 5:32 pm
by megavolt85
MoeFoh wrote: Wed May 22, 2024 5:01 pm No vibration ability detected. 240p TS doesn't show a JumpPack like it should.
alas, I have no information on how this controller turns on vibration

Re: USB4MAPLE adapter

Posted: Thu May 23, 2024 1:02 am
by MoeFoh
megavolt85 wrote: Wed May 22, 2024 5:32 pm
MoeFoh wrote: Wed May 22, 2024 5:01 pm No vibration ability detected. 240p TS doesn't show a JumpPack like it should.
alas, I have no information on how this controller turns on vibration
Looks like 8bitdo doesn't support vibration in ANY of its controllers (that have motors) in d-input mode :( , only x-input & Switch modes. Checked with gamepad-tester.com and the vibration field is greyed-out when the controller is in d-input mode.

Re: USB4MAPLE adapter

Posted: Fri May 24, 2024 1:49 pm
by megavolt85
PS5 Dualsense now supported, vibration too
usb4maple(24.05.24).7z
(52.3 KiB) Downloaded 161 times

Re: USB4MAPLE adapter

Posted: Fri May 24, 2024 8:01 pm
by BaronBurdock
Has anyone made an adapter that involved soldering a female USB to the test pads of a regular pi pico? I made two that way, but its behaving weirdly when I plug a 360 controller in.

I tried playing Quake 3 with the all analog mode enabled and every time I pulled the right trigger it disconnected and went back to whatever the top left mode is on the xbox 360 button. Sometimes it would get stuck turning.

In Tony Hawk, it kept saying it was disconnected and reconnected. I figured it was bad soldering at first, but both cables are behaving this way and I tested to make sure something wasnt shorting out. Really weird

Re: USB4MAPLE adapter

Posted: Sat May 25, 2024 6:31 am
by megavolt85
your problem is more like a bad power supply, when vibration is turned on, the voltage drops significantly and the controller turns off

Re: USB4MAPLE adapter

Posted: Sat May 25, 2024 7:32 am
by BaronBurdock
Yup, thats exactly it. I tested it with 3rd Strike, as soon as I turned the vibrate on in the menus the controller reset. I'll look into that. Thanks

Re: USB4MAPLE adapter

Posted: Sat May 25, 2024 10:36 am
by rpf16rj
pcwzrd13 wrote: Thu Apr 11, 2024 11:54 am My custom enclosure is now available for download from Printables! :-) https://www.printables.com/model/840316 ... e-by-megav

There's no logo on the model itself. It's just in the picture.
adapter.png
Hey @pcwzrd13, I began on a 3d printer and used your model, thank you for a great job, it is amazing.

Image

Image

Image

Could you create the model 3d for rp2040 pico, if don't ask much? This one:

Image