**I highly recommend reading this whole guide in advance if you plan on doing this so you know exactly what you need.
This is not the cheapest setup, but if you can find the materials for a good price then it's totally worth it. Since this method of connection is completely seamless to connect like a bba, but allows you to connect to anything since it's still using dial up.
Here is what you need to set this up:
-Router (any broadband router should do)
-Phone Line Simulator (I'm using a Teltone TLS3) **See Below for Phone Simulators confirmed to work with this
-Dreamcast w/ 56k Modem (Model A and B will both work)
-2 Telephone cords (If connecting two Dreamcasts simultaneously you will need 4 telephone cords, and 6 for three simultaneous Dreamcast connections)
These are the Phone Line Simulators which have been used so far and are confirmed to work:
- -Teltone TLS2
So onto the features of this connection method:
-19Kbps connection speed (Theoretical max of 33.6Kbps per line, using an added V92 serial modem it would be 48Kbps)
-130ms latency (over LAN)
-No phone line is required
-Dreamcast will be on the same subnet as PC's on your network (ie, if your router is 192.168.1.1, then Dreamcast can be anything from 192.168.1.2 to 192.168.1.255)
-As a result of being on the same subnet, it is managed completely by your broadband router as with all modern network devices ( You can even put Dreamcast in DMZ if you so choose)
-The Netopia R2000/R2020 will automatically answer Dreamcast's call
-This works with model A and model B Dreamcast Modems both without the use of a line voltage inducer
-The phone line simulator will supply the dial tone for Quake 3 and any other game which does not support blind dial
-You can connect 2 (3 if you attached a serial modem) Dreamcasts simultaneously so long as there are sufficient lines on your phone line simulator.
-Because Dreamcast is seen on the same subnet as other PCs on the LAN, you can use drdns and connect to PSO using the same method as a BBA without the need to use a codebreaker or autoconnect disc.
I am not going to go into detail on how to set up a third simultaneous connection with the use of an external 56k modem connected to the Netopia router's serial port because I do not have a serial modem to test with and it requires some configuration options to be changed. As a result, this guide is for connecting one or two Dreamcasts simultaneously to Netopia router.
**Note that I am using a Netopia R2020 in this guide. However the setup should be near identical to the setup of a Netopia R2000 or R2121.
Before I start the guide I would just like to say that if you are purchasing a phone line simulator to make sure it either includes the documentation, or it is available online. The reason I say this is that you will need to know what telephone number to tell Dreamcast to dial in order to reach the other line on your phone line simulator. For example on mine I must dial "40" to reach line 1.
Okay so on to the guide..
STEP 1 - Initial Setup
So first grab your Netopia router. Inspect the back of it and make sure the uplink button is not depressed. It should be in "normal" mode.
Now plug the power cord in and get an ethernet cable and connect the Netopia router directly to a computer with any of its 8 LAN ports. Make sure the computer you are connecting it to is not connected to any other networks (To avoid any IP conflicts). Now press the power button and turn on the Netopia.
The default ip address of the netopia router is 192.168.1.1 . However this device is not managed from a web interface like most routers. It is managed from a terminal/command prompt. Don't let this turn you off it's actually quite user-friendly. So to access your netopia router first open up a terminal (linux) or command prompt (windows). Then type this:
Code: Select all
**In windows if the command "telnet" is not recognized you must enable it first. To do this go to Start > Control Panel > Programs and Features > Turn Windows features on or off, then check "Telnet Client" and hit OK.
If you bought your Netopia second-hand and for some reason the IP address is not initially 192.168.1.1 you will need to do a hard reset first using a metal paper clip. For more info on how to do this check the section at the end of this guide.
Now you see this:
**A few notes on how to navigate through the netopia interface in cmd prompt/terminal... Up and down arrows move between options. Enter button selects an option. Esc backs out of an option. Tab enables/disables some options. When typing in values such as an IP address, type the whole value in first then hit enter.
First what you want to do is change your Netopia router's IP address to one that is on the same subnet as your broadband router. You also must set the default gateway to your broadband router's IP address and set the primary DNS to your broadband router as well or a different DNS if you so choose. To do this navigate to System Configuration > IP Setup Below you can see how I have it configured. My broadband router's IP address is 192.168.1.1 and I set the Netopia to 192.168.1.2 .
Then on the same screen navigate to "IP Address Serving" and change "IP Address Serving Mode" to Disabled.
Now back out to the main menu of your Netopia router. Go to Utilities & Diagnostics > Restart System and hit continue. This will reboot your Netopia router. Make note of where is, as you will need to reboot after all main configuration changes to your Netopia router.
**Be aware that once changing the Netopia router's IP and powering off you will no longer be connected to it. And unless you have a static IP setup you will also not be able to connect after disabling DCHP. However this won't matter once you are at the next step since your gateway will be your broadband router. Just be aware the next time you type "telnet [ip]" it is the new IP Address you changed your Netopia router to.
STEP 2 - Integration with LAN / Firmware Upgrade
Okay, now disconnect your Netopia Router from your computer and connect it to one of the LAN ports on your broadband router. And connect your PC to your router again. Then connect a telphone cord to one of the Line ports on the Netopia router (it doesn't look like it will fit but it will). Connect the other end of the cord to a line on your phone line simulator. Then on a separate line of the phone line simulator connect it to your Dreamcast modem.
Once everything is reconnected use telnet again this time to the new IP address you assigned to the netopia router.
Code: Select all
telnet [new ip]
Now what we are going to do is upgrade the firmware to the newest version. It may not be necessary to upgrade the router firmware depending on which version your Netopia router is already running. However, I highly recommend you do to avoid any complications in going through my guide, as I have the latest version.
You should now have internet access to the netopia router. So from the main page navigate to Utilities & Diagnostics > Trivial File Transfer Protocol (TFTP) Next type in the following:
Code: Select all
TFTP Server Name: ftp.netopia.com
Firmware File Name: nir4113.bin
Then hit enter on "GET ROUTER FIRMWARE FROM SERVER" as seen below. Be sure to not lose power or internet while upgrading.
After the firmware is done downloading, your Netopia router will automatically reset and start making a light show with its LEDs.
**If for some reason your Netopia router fails to connect to the netopia ftp server and you believe it is in fact connected to the internet, you can do the following.. Download the file attached to this post named "nir4113.rar". Then extract the winrar archive and host it on a local PC using FTP server software such as filezilla server. On your Netopia router, then change the server name from "ftp.netopia.com" to your local PC's IP address and select "GET ROUTER FIRMWARE FROM SERVER".
*****The netopia ftp/tftp doesn't appear to work anymore or no longer has the netopia r2020/r2000 firmware stored on it. Therefore, unless something changes, the above method in quotations will not work. Instead do the following to update your netopia firmware:
1) Download & install Tftpd from here: http://tftpd32.jounin.net/tftpd32_download.html
2) Create a folder on your desktop and name it like "TFTP Folder" or something similar.
3) Open Tftpd and go to settings. In global tab, Uncheck "Enable IPv6". In tftp tab for base directory browse to the TFTP Folder you created and then click OK.
Note that your PC's local IP address is listed next to server interface on the main window of tftpd in case you don't know it.
4) Download nir4113.rar which is attached to this post and extract nir4113.bin to your TFTP Folder.
5) Open up a telnet connection with your netopia router and go to Utilities & Diagnostics > Trivial File Transfer Protocol (TFTP). Set the TFTP Server Name to your PC's local IP address. Set the Firmware File name to nir4113.bin . Then click GET ROUTER FIRMWARE FROM SERVER and it should download and install the firmware directly from your computer, assuming your PC isn't blocking tftpd with firewall.
[OPTIONAL]I also just found the lastest firmware for the internal 56k modems inside of the netopia.. Netopia doesn't appear to host this file anymore, but i found it archived at tellurian.com. These use a separate firmware from the netopia router itself. I installed this firmware as well, so I know it does work. I'm not sure if the performance is much different though so I would say this is optional. I will attach this firmware to the post as well though. If you wish to update the 56k modems' firmwares, it is quite similar to updating the netopia firmware. To do so:
1) Download the v220.rar file attached, unrar v220.bin to your TFTP Folder.
2) Then again go to Utilities & Diagnostics > Trivial File Transfer Protocol (TFTP) on your netopia router via telnet.
3) Set the file name to v220.bin , the server name to your PC's local ip, and then click GET WAN MODULE (MODEM) FIRMWARE FROM SERVER...
I did notice when I updated the modem firmware that it stopped at 100% complete and did not go back to idle in tftp transfer state. I just rebooted the netopia at that point and it seems to have updated correctly. In Statistics and Logs > System Information I now see "V2.210-NC-V90_2M_DLS" for my modems' version. The v220.bin file corresponds to v2210c modem firmware so it appears to be correct.
STEP 3 - Configuring Dial-in on your Netopia Router
First go to WAN Configuration > Add Connection Profile. On that page:
Code: Select all
Profile Name: Your Choice
Profile Enabled: Yes
Encapsulation Type: PPP
Next go to "Encapsulation Options". Here use this configuration:
Code: Select all
Data Compression: None
Send Authentication: PAP
Send User Name:
Receive User Name: dream
Receive Password: dreamcast
Channel Usage: Dynamic
Dial on Demand: Yes
Bandwidth Allocation: Auto
And here is an image of that...
Now back out back to the connection profile page you were just on. Go to "IP Profile Parameters". Use this configuration:
Code: Select all
Address Translation Enabled: No
IP Addressing: Unnumbered
Negotiate LAN IP Addr/Mask: No
Remote IP Address: 192.168.1.10 (This is Dreamcast's IP Address. Set it to whatever you like on the same subnet as your LAN)
Remote IP Mask: 255.255.255.255
Then go to "Remove Filter Set" and hit enter. Heres the image of this page:
Back out again to the configuration profile page. Now go to "Telco Options" and hit enter. Config for this page is the following:
Code: Select all
Dial: Dial In Only
Number to Dial:
Alternate Site to Dial:
Idle Timeout (seconds): 0
CNA Validation Number:
CompuServe Login Enabled: No
Image of the telco page:
Now go back out again to the connection profile page. Go to "COMMIT" and hit enter. Now reboot your Netopia router as done previously in the guide (Utilities & Diagnostics > Restart System and hit continue.)
Congratulations!! You have now configured the netopia for dial-in from Dreamcast. If you plan to connect multiple Dreamcasts simultaneously you will need to create a connection profile for each Dreamcast using a different user/pass and remote IP address for each. However all other settings will remain the same. For the remainder of the guide I will be assuming the user/pass used is dream/dreamcast as configured above.
STEP 4 - Exploring Some Features of your Netopia Router
Feel free to check out the different features on your router now that it is configured.
In Statistics & Logs > WAN Event History you can see in real time what your modems are doing. This is useful to see whats happening when your modem is connecting to Dreamcast.
In Statistics & Logs > General Statistics you can see in real time how much data and packets are being sent and received by the netopia router, modem 1, modem 2, and the serial port.
In WAN Configuration > WAN (Wide Area Network) Setup > MODEM (Wan Module 1 and 2) Setup you can change the modem speaker volume or disable it. You can also specify when you want it to make noise.
STEP 5 - Configuring Dreamcast
Put your Dreamcast web browser in and go to internet options. Use these settings:
Code: Select all
Your Real Name: (Anything will work here)
User Login: dream (Put in the user name that you typed in your connection profile)
Password: dreamcast (Put in the password that you typed in your connection profile)
Dial Up Number: 40 (Type in the number associated with the line on your phone line simulator which is being dialed. Find this out in your phone line simulator manual/documentation. On the Teltone TLS3 dialing "40" rings the first line)
Backup number: (Leave blank)
Area code you are dialing from: (Leave blank)
Long distance call prefix: (Leave blank)
Call waiting prefix: (Leave blank)
Outside dialing prefix: (Leave blank)
Modem Init: AT&F0 (usually the default. Last character is the number zero)
Dial area code: Off
Blind Dial: Off
Thats it!!! You can now go and connect with your web browser or any working game which uses dial up. I suggest putting your Dreamcast in a DMZ from your router to avoid any port issues otherwise you can port forward from your router if need be to the ip address you assigned Dreamcast in the connection profile on your Netopia router.
Make sure your phone line simulator is powered on while using the Netopia router with Dreamcast otherwise it will fail to answer the call and report no dial tone. If you are connecting multiple Dreamcasts simultaneously you will need 2 lines on your phone line simulator for each Dreamcast you are connecting.
If you wish to connect multiple Dreamcasts to Netopia router which you do not plan on connecting simultaneously you can connect them using an RJ-11 splitter to a single line port on the Netopia router and configure them all to connect to the same dial in profile.
I have tested PSO, Quake 3 Arena, Max Pool, 4x4 Evolution, and StarLancer. With 4x4 Evolution, Max Pool and StarLancer it sometimes takes a couple tries for it to connect. If the Netopia router does fail to answer a call, wait for the Channel and Ready LEDs to go out before attempting to redial. Once the game is connected you should not have any issues.
The Netopia R2020 User Manual is attached if you wish to read more about it.
Feel free to leave any questions or comments. I will update this if anything needs to be changed. However so far this is working perfectly.
Here is a video of me connecting to Quake 3 Arena with the netopia:
Here are a couple photos of my Netopia R2020:
And here is a video tutorial which pcwzrd13 created for connecting DC using this method: [youtube]http://www.youtube.com/watch?v=vhXQjy-DsBs[/youtube]
This follows the guide fairly close, but some details might be slightly different depending on your setup with this.
Teltone TLS2 & TLS3 Users
There is no reason you have to use a TLS3 for this guide, other phone line simulators will work, but I figured I would include a short note on the TLS3 since most people following this seem to be using that as their phone line simulator.
So first of all I should say that my tls3 randomly stopped working about 8 months after I purchased it. Which I later found was because the fuse went bad (it didn't actualy blow). These things were manufactured in the early 90s so I guess it just went bad after years of use. If this happens to you, or if the Teltone occasionally doesn't turn on for some reason when you flip the switch you should replace the fuse in the back. You can replace it with a 0.315A 250V 5x20mm fuse which can be purchased at radioshack, or at your local electronics store. --> http://www.radioshack.com/product/index ... Id=2103762
I'm not sure what the difference is between the "GS" and "LS" modes for the phone lines on this thing, but I found that the netopia only seems to work right when both lines are in "LS" mode.
***For TLS2 Users: Station 40 should be set to "LS" and Station 29 should be set to "GS" --Thanks to Atreyu187 for pointing this out
And finally, you may have figured this out but the phone number to the line labeled "STATION 40" is "40" and the phone number for the line labeled "STATION 29" is "29". On some of the higher model Teltone phone line simulators the phone numbers are programmable.
Here are the default phone numbers for all Teltone models:
TLS, TLS-2, TLS-3: 29, 40
TLS-3A-01: 29, 40, 101, 102, 201, 202, any 7 digit number, any eleven digit number
TLS-3B-01: 101/201, 102/202
TLS-4/5: 101/201, 102/202, 103/203, 104/204
For more info: http://www.teltone.com/support/faq.htm#tls
Routers known to cause issues with this setup
There is an issue where Quake 3 Arena freezes when it is trying to retrieve the server list after connecting when the netopia is using my new router's (Linksys E3200) DNS relay. This hasn't been an issue with any other router I've used, but it is easily remedied by setting your ISP's DNS servers in the Netopia IP Setup instead of using your router's IP address or "0.0.0.0". If you experience anything similar, just set your DNS servers manually in the Netopia IP setup instead of using your router's DNS relay.
The issue with the DIR-615 is a pretty major one and it appears to be specific to this setup (ie dialing into the netopia on your LAN). I noticed this when i bought one to replace a Netgear router about 6 months ago. Essentially what happens is every time something dials into your Netopia router the D-Link DIR-615 acting as primary router on your network instantly crashes and reboots, disconnecting all clients on your LAN including PCs and such. This happened using the latest firmware version for the router which I believe is 3.13NA. The fact that this router can crash from certain network activity is alone reason for me to advise anyone not to use this router if it is an option. However there is a solution to this problem if you already own one. Instead of returning the router I decided to install DD-WRT( http://www.dd-wrt.com/site/index ) on it which is a custom router firmware and this completely resolved the issue I was having which is purely software-related.
The problem with the D-Link DIR-655 should actually be an issue for anyone using a dial-in server on their LAN (whether PC-DC server or this setup) when using this as their primary router. As far as I can tell it effects only 2 Dreamcast games, that is 4x4 Evolution and StarLancer. This problem occurs with the latest firmware version 1.35NA. So the problem with this router is it blocks both incoming and outgoing TCP packets with 4x4 EVO and Starlancer, preventing either game from connecting. In the router logs it shows an error message indicating that it sees the TCP packets from both games as being invalid. This is the exact error message:
Code: Select all
Blocked TCP packet from 192.168.1.10:6898 to 126.96.36.199:80 as control SYN:PSH in not valid
How to do a hard reset of your Netopia Router
So for some of you it may be necessary to do a hard reset of your netopia to get to back to factory default settings. I didn't have to do this, but I know some other people who followed this guide have needed to. For some reason there is no explanation in how to do this in the user manual and it isn't exactly straight forward so I'm gonna explain how you go about doing this.
You will need a metal paper clip first of all. Make sure your netopia is plugged in and powered on. Then what you want to do is flip it over and locate the slot in the picture below which is about halfway up.
Now insert your folded metal paperclip into the slot until you meet resistance. You will hear the router click if you have pressed the reset button properly. You will then be back to default settings.