It works perfect with both Mayflash F300 and Viper v2 Pro.
thank you very much!!!
Moderators: pcwzrd13, deluxux, VasiliyRS
It works perfect with both Mayflash F300 and Viper v2 Pro.
you need any usb-uartrobinhoodie wrote: ↑Fri May 10, 2024 10:34 pm I want to add to the supported sticks list. What do I need to generate the log file?
no, only arcade stick mode
Code: Select all
HID device address = 1, instance = 0 is mounted
HID Interface Protocol = None VID = 054C PID = 0268
HID has 1 reports
VID = 054c, PID = 0268
Protocol 0
HID receive desc report:
05 01 09 04 A1 01 A1 02 85 01 75 08 95 01 15 00
26 FF 00 81 03 75 01 95 0D 15 00 25 01 35 00 45
01 05 09 19 01 29 0D 81 02 75 01 95 03 06 00 FF
81 03 05 01 25 07 46 3B 01 75 04 95 01 65 14 09
39 81 42 65 00 75 01 95 0C 06 00 FF 81 03 15 00
26 FF 00 05 01 09 01 A1 00 75 08 95 04 15 00 15
00 15 00 35 00 35 00 46 FF 00 09 30 09 31 09 32
09 35 81 02 C0 05 01 75 08 95 27 09 01 81 02 75
08 95 30 09 01 91 02 75 08 95 30 09 01 B1 02 C0
A1 02 85 02 75 08 95 30 09 01 B1 02 C0 A1 02 85
EE 75 08 95 30 09 01 B1 02 C0 A1 02 85 FE 75 08
95 30 09 01 B1 02 C0 C0
no, this connection method will not work on any firmware.
it's use Dualshock 3 VID and PID, if it doesn't work now, then I can't add support for it because the ID is already occupied by the DS3 controller
Code: Select all
Starting
HID device address = 1, instance = 0 is mounted
HID Interface Protocol = None VID = 20D6 PID = A711
HID has 1 reports
VID = 20d6, PID = a711
Protocol 0
HID receive desc report:
05 01 09 05 A1 01 15 00 25 01 35 00 45 01 75 01
95 0E 05 09 19 01 29 0E 81 02 95 02 81 01 05 01
25 07 46 3B 01 75 04 95 01 65 14 09 39 81 42 65
00 95 01 81 01 26 FF 00 46 FF 00 09 30 09 31 09
32 09 35 75 08 95 04 81 02 75 08 95 01 81 03 C0
00 00 0F 80 80 80 80 00
Left Stick UP: 00 00 0F 80 00 80 80 00
Left Stick DOWN: 00 00 0F 80 FF 80 80 00
Left Stick LEFT: 00 00 0F 00 80 80 80 00
Left Stick RIGHT: 00 00 0F FF 80 80 80 00
Right Stick UP: 00 00 0F 80 80 80 00 00
Right Stick DOWN: 00 00 0F 80 80 80 FF 00
Right Stick LEFT: 00 00 0F 80 80 00 80 00
Right Stick RIGHT: 00 00 0F 80 80 FF 80 00
d-pad up = 00 00 00 80 80 80 80 00
d-pad down = 00 00 04 80 80 80 80 00
d-pad left = 00 00 06 80 80 80 80 00
d-pad right = 00 00 02 80 80 80 80 00
Y = 01 00 0F 80 80 80 80 00
X = 08 00 0F 80 80 80 80 00
B = 02 00 0F 80 80 80 80 00
A = 04 00 0F 80 80 80 80 00
L = 10 00 0F 80 80 80 80 00
R = 20 00 0F 80 80 80 80 00
ZL = 40 00 0F 80 80 80 80 00
ZR = 80 00 0F 80 80 80 80 00
start = 00 02 0F 80 80 80 80 00
select = 00 01 0F 80 80 80 80 00
home = 00 10 0F 80 80 80 80 00
fixed
looks the same as the regular version, added PID to the list, test it
Code: Select all
Starting
HID device address = 1, instance = 0 is mounted
HID Interface Protocol = None VID = 2DC8 PID = 5001
HID has 1 reports
VID = 2dc8, PID = 5001
Protocol 0
HID receive desc report:
05 01 09 05 A1 01 15 00 25 01 35 00 45 01 75 01
95 0F 05 09 19 01 29 0F 81 02 95 01 81 01 05 01
25 07 46 3B 01 75 04 95 01 65 14 09 39 81 42 65
00 95 01 81 01 26 FF 00 46 FF 00 09 30 09 31 09
32 09 35 75 08 95 04 81 02 05 02 15 00 26 FF 00
09 C4 09 C5 95 02 75 08 81 02 05 08 09 43 15 00
26 FF 00 35 00 46 FF 00 75 08 95 02 91 82 09 44
91 82 09 45 91 82 09 46 91 82 C0
00 00 0F 7F 7F 7F 7F 00 00
d-pad up = 00 00 0F 7F 00 7F 7F 00 00
d-pad down = 00 00 0F 7F FF 7F 7F 00 00
d-pad left = 00 00 0F 00 7F 7F 7F 00 00
d-pad right = 00 00 0F FF 7F 7F 7F 00 00
X = 10 00 0F 7F 7F 7F 7F 00 00
Y = 08 00 0F 7F 7F 7F 7F 00 00
Z= 40 00 0F 7F 7F 7F 7F 00 00
A = 02 00 0F 7F 7F 7F 7F 00 00
B = 01 00 0F 7F 7F 7F 7F 00 00
C = 80 00 0F 7F 7F 7F 7F 00 00
MODE = 00 04 0F 7F 7F 7F 7F 00 00
start = 00 08 0F 80 80 80 80 00
Thanks Megavolt, all working normally, I tested the PowerA ones too