USB4MAPLE adapter

[megavolt85]

Picked up an official ps4 controller.

fixed

Mayflash SS Controller Adapter

added

usb4maple(16.05.24).7z

(50.59 KiB) Downloaded 121 times

[pcwzrd13]

@Megavolt Are you able to adjust the analog sensitivity in dual-stick mode? In Q3A and UT, I have to turn the in-game sensitivity almost down to 0. Even then I think it's a bit too sensitive. I think if you could cut it in half, it would be good.

Edit: I should clarify that it's just the right stick that's too sensitive. The left is fine.

[Vespa]

@megavolt85 SS adapter works great, thank you for your hard work! (=

@pcwzrd13 Thank you for continuing to maintain the wiki

[MoeFoh]

@megavolt85

ps4 update:
L1, R1 - good

Twin Stick Mode:
Right Analog Stick Now -
Up = Left
Left = Down
Down = Up
Right = Right - good

Front light is working to show mode (that's cool).
ps + cross = red
ps + circle = white
ps + triangle = blue
ps + square = green

Rumble - tested and working!

[LeSpank]

Does anytime have any tips on how to identify the wires in the controller cord? I'm about to chop up an extension cable to make a USB4MAPLE adapter and was hoping I wouldn't need to mess around with the connector itself..

[megavolt85]

@Megavolt Are you able to adjust the analog sensitivity in dual-stick mode? In Q3A and UT, I have to turn the in-game sensitivity almost down to 0. Even then I think it's a bit too sensitive. I think if you could cut it in half, it would be good.

test now

Twin Stick Mode:
Right Analog Stick Now -
Up = Left
Left = Down
Down = Up
Right = Right - good

test now

Does anytime have any tips on how to identify the wires in the controller cord?

you can use multimetr or open connector and look which color is connected to which pin

fixed PS4 Twin Stick mode
fixed sensivity for dual-stick mode
added PXN-F16 flight stick (VID = 11FF PID = 083A)

usb4maple(17.05.24).7z

(50.93 KiB) Downloaded 128 times

[pcwzrd13]

@Megavolt Are you able to adjust the analog sensitivity in dual-stick mode? In Q3A and UT, I have to turn the in-game sensitivity almost down to 0. Even then I think it's a bit too sensitive. I think if you could cut it in half, it would be good.

test now

That's better but I think you could even reduce it farther. This is where I have the sensitivity in Q3A now. For me this is about perfect.

Obviously this is a matter of preference but if you leave it at default, it's still way too sensitive.

[megavolt85]

it was a halving of sensitivity, try reducing sensitivity by 4 times

usb4maple(17.05.24).7z

(50.94 KiB) Downloaded 75 times

[pcwzrd13]

Thanks Megavolt! Yeah I think that's good. Still have to adjust it a bit but that's fine. At least you don't have to crank it down to almost nothing. lol

[MoeFoh]

@megavolt85

ps4 update - all mappings are good now. thanks.

Note from the sensitivity change in the last firmware in dual-analog (ps + square) mode:
From 240p Test Suite:
right analog up = 0 to 32
right analog down = 0 to 31
left analog left = 0 to 32
right analog right = 0 to 32
as expected with reduction to 1/4.

What are those games doing as far as reading the analog right stick - why are they not using a range of 0 to 255?
What controller is pcwzrd13 using for the testing?
I wonder how this will affect other titles?
Edit: so the game thinks a mouse is attached to 2nd analog.